Process difficulty / 2026-11-20

Where the difficulty of aramid coating actually lies: four requirements that pull in opposite directions

The process itself is a company trade secret and is not published, but the reasons behind the difficulty can be discussed: heat resistance and wetting pull in opposite directions, mechanical strength is a curve against temperature, the thickness budget narrows the scheme space, and batch consistency is harder than a single-batch peak. This article explains those four and gives five checkable actions for selection and verification.

01

The note

Figures are quoted with their test condition and standard; project-specific data is confirmed one to one at the sample stage.

What this article does not cover

The preparation process, the coating composition and the process window of an aramid-coated separator are company trade secrets and are not published. Writing out process steps would serve no purpose and would not be appropriate.

What can be discussed openly is the **difficulty** itself: it explains why a certain figure is hard to reach together with the others, why some of them trade against each other, and what to look at during selection and verification. The discussion below stays at that level.

Difficulty one: heat resistance and wetting pull in opposite directions

Raising heat resistance usually means a more stable, lower-surface-energy surface that changes less under thermal treatment. Raising electrolyte wetting usually means a more liquid-friendly surface with more open porosity.

Those pull against each other on the same surface. What the company product does is let the **coating interior** carry the porosity and the wetting function, while the **separator as a whole** keeps its thermal shrinkage at 1-2% (180 °C / 30 min, air atmosphere, GB/T 36363-2018) and a breakdown temperature above 400 °C. In other words, thermal stability is carried by the intrinsic property of the material, not bought by giving up wetting.

This is why asking how hard an aramid-coated separator is to make is not really about pushing one figure to its limit. It is about finding a repeatable combination across several figures — which is the common nature of the difficulties below.

Difficulty two: mechanical strength is not a number but a curve against temperature

Puncture strength and peel strength, if measured only at room temperature, cannot show what a coating has changed. What matters for a cell under thermal duty is how the coating behaves after heat treatment.

The company test basis reports conclusions by temperature window: below 145 °C the treatment does not reduce puncture strength, and after 145 °C / 1 h and 140 °C / 1 h the puncture strength is unchanged or slightly higher; in the 150 °C / 0.5 h window the double-side coated scheme retains 40-60%, and in the 180 °C / 0.5 h window it still retains more than 20%.

Read as a curve rather than as a single value, this set of figures is far more reliable than any isolated number. It is also why the question of whether strength drops after coating only has an answer once a temperature condition is attached.

Difficulty three: the thickness budget limits the scheme space

Coating adds thickness. Once the energy density target is fixed, the thickness space available to the separator is fixed too, which directly narrows the choice of coating scheme.

The six models on sale carry nominal total thicknesses of 9 / 11 / 13 / 14 µm. Across that span the mechanical and thermal behaviour of the single-side, double-side and semi-solid schemes are not the same, and the strength gain from added thickness is not linear.

The practical meaning of process difficulty is therefore: within the thickness space given, how far does the coating have to go to be sufficient. That is a closer question to reality than how much can be achieved.

Difficulty four: batch consistency is harder than a single-batch peak

Achieving a result once at sample stage and achieving it in every production batch are problems of different difficulty. The second requires the process window itself to have margin, rather than running exactly along a single control line.

For the company product this shows up as the double-side coated scheme meeting the peel strength acceptance criterion (>30 N/m, GB/T 7122-96) stably across a **wider range of process conditions**, rather than clearing it only under one set of conditions.

For long-running duties such as grid-scale storage projects, the spread between batches has to be held inside a checkable range, and that often matters more to the project than the peak figures of one batch.

What to check during selection and verification

Turned into checkable steps, the above amounts to roughly five actions.

First, establish the thickness budget and the thermal duty window of the target cell, since those two define the scheme space. Second, check that the shrinkage acceptance condition (180 °C / 30 min, air atmosphere) matches what your application requires, otherwise there is nothing to compare. Third, look at which temperature band the puncture strength retention falls into, rather than at one retention figure on its own. Fourth, check whether air permeability (Gurley, about 226-366 s) and separator porosity as a whole (about 35%-45%) meet the wetting and rate demands. Fifth, check the batch consistency basis — whether the supplier can give a distribution between batches rather than a single pass line.

When all five line up, the discussion at process level has reached a verifiable place. The specific coating composition and process parameters are outside the published scope and can be provided in a one-to-one technical discussion.

02

Related pages

To discuss a parameter range for a specific cell architecture, contact the technical team directly.

← Back to insights