SEPARATOR FILM / Core business

Two business lines,
one measurable material

Semi-solid aramid-coated separators and custom composite technical support. Thickness, porosity and thermal shrinkage are confirmed against the cell architecture instead of quoted in isolation.

01

Business lines

One line turns the material into a measurable number, the other turns the scheme into a concrete cell architecture; the two lines meet at the sample stage.

01

Semi-solid aramid-coated separators

Flagship product
EV batteriesEnergy storageHigh-safety applications

An aramid coating layer is introduced on the separator surface for cell chemistries with high safety requirements, balancing high-temperature resistance, interface adhesion and mechanical retention after heat exposure.

  • Six models on sale with total thickness of 9 / 11 / 13 / 14 µm, covering single-side, double-side and semi-solid structures
  • Thermal shrinkage 1-2% (180 °C / 30 min); breakdown temperature above 400 °C
  • Puncture strength retention after heat treatment: 40%-60% in the 150 °C / 0.5 h band, above 20% in the 180 °C / 0.5 h band
  • Internal acceptance criterion for peel strength > 30 N/m (GB/T 7122-96)
02

Custom composite and technical support

Technical collaboration
EV batteriesEnergy storageConsumer electronics

Structural combinations and process adjustments are worked out around the cell architecture, with the technical team taking part in parameter confirmation and failure analysis from the sample stage.

  • Cell design and duty cycle are aligned first; parameter ranges are discussed afterwards
  • Test data and failure-analysis suggestions are provided during sample validation
  • A technical contact window is kept open during mass production to handle batch variation
  • Coating composition and process parameters are company trade secrets and are not disclosed
02

Specification range

Thickness follows the series and the coating structure; thermal shrinkage, puncture strength and porosity are nominal values, and the test conditions are subject to technical confirmation.

Aramid-coated separators on sale and their total thickness
ModelProduct nameTotal thickness (µm)Scheme
JTF-R20LA8Aramid-coated separator9Aramid-coated
JTF-R10LPAramid-coated separator11Aramid-coated
JTF-R208BLAramid-coated separator11Aramid-coated
JTF-R10DHSemi-solid aramid-coated separator13Semi-solid
JTF-R208DLSemi-solid aramid-coated separator14Semi-solid
JTF-R20LD8Aramid-coated separator14Aramid-coated

The figures above are nominal; measured values for a given batch follow the test report. Custom composite structures are confirmed per project.

03

Key figures

No figure is published before it is confirmed. Every metric carries its measurement condition; the matching data is given once the scenario is agreed.

1-2% Thermal shrinkage Condition: 180 °C / 30 min, air atmosphere, MD and TD shrinkage (GB/T 36363-2018)
>400°C Breakdown temperature Condition: N2 atmosphere, 100 °C/min ramp, 0.02 N tension (GB/T 36800-2018)
35-45% Separator porosity Measured range over multi-batch coated samples, derived from thickness, areal density and slurry density
Scanning electron micrograph of the aramid-coated separator surface
Separator surface, SEM top view (company measurement). Nanoscale pore formation gives a uniform porous morphology, which is the microscopic basis for low contact angle and high wettability
04

Milestones

Four confirmation points from requirement to delivery. Each one leaves a record, so an anomaly can be traced back to a concrete step.

01

Requirement confirmation

Align the cell architecture, application scenario and the range of metrics that matter.

02

Sample validation

Provide test data and failure-analysis suggestions, and narrow down the parameter range.

03

Technical liaison

Keep a window open during mass production to handle batch variation and failure analysis.

04

Delivery and traceability

Moisture-proof packaging with batch identification; retained samples archived in parallel.

05

Testing capability

The company has built a pilot production line, an R&D laboratory line and a testing laboratory, equipped with coating, slitting and separator drying equipment.